Buy Low Price From Here Now
This is a factory reconditioned power tool. Reconditioned generally means that the tool has been returned to the manufacturer, who brings the tool back to like new condition. Some tools may contain cosmetic blemishes. Includes 18V Cordless LXT Lithium-Ion 1/2" Hammer Driver-Drill - BHP454-R, (2) 18 Volt 3.0 Ah LXT Lithium-Ion Batteries - 194205-3, (2) Bits, (1) Grip, Optimum Charger - DC18RA, Carrying Case, Operating Manual
Readmore
Technical Details
- Makita built 4 pole motor delivers 560 in lbs of maximum torque- 2 speed all metal transmission(0-400/ 0-1700RPM) covers a wide range of drilling, driving and hammer applications
- Compact design at only 9-9/16" long
- 2 trigger forward built-in LED lights illuminate the work area
- Ergonomic shape fits like a glove with even pressure and easy control
See more technical details
By Bryan Sanders (Chicago)
I bought two of these kits and the discount is hefty but at a price. Both kits lacked the depth rod, one lacked the side clip, both lacked the white plastic covers for the spare batteries, and one kit had a defective battery charger. Other than that the drill kits were as advertised.
Drill performance is adequate for most jobs and adjusting the speed range and hammer and driver modes is easy to do. The chucks tighten easily to hold even small drill bits but with vibration the chucks will loosen and you need to stop and retighten them.
Drill torque is average for 18 volt drills, better than the 450 in. lb. models but not in the same league as the Milwaukee 2611 much less the DeWalt DCD940 and DCD970 drills. This lower torque is compounded by the lack of a 3-speed gear box like the top of the line DeWalt drills. Strange that the manufacturers make lower powered cordless drills but do not see the need to provide more gear range options to compensate (other than DeWalt and Ridgid).
Battery charge time is good but Makita recommends a 60 minute cool down period after charging so for maximum battery life a 90 minute recharge time is evidently required.
The 3 Ah batteries do not have recessed contacts so the plastic covers are important for the spares. Holes per charge is average for 18 volt drills with full size batteries.
The Makita drills are lighter than comparable drills from DeWalt and a lot of that is the result of a lighter battery. The Makita 3 Ah battery weighs about 22 oz. while the DeWalt XRP batteries weigh 37 oz. or nearly a full pound more. The DeWalt battery's weight is offset by being able to deliver more power to the drill motor for heavy duty use and it provides a lot more holes per charge.
With lithium-ion drills I have read that they will not provide as much peak power as a NiCad and that has been my experience as well. I tend to just buy the next size up and get a drill with a higher power or torque rating and this works well most of the time.
The side handle that Makita makes is my favorite in that it locks in any position and is smooth to tighten compared to the DeWalt design. It is not as long as the handle that Milwaukee provides with the 2611 drills but it is also not limited to 90 degrees like the Milwaukee side handle. Makita does not provide a home for the side handle in the case which it not at all unusual. Only Milwaukee take the trouble to create a carry case that holds everything for each kit instead of taking the one size fits all that Makita, Hitachi, DeWalt, and others take. For attention to the details Milwaukee has a sizable lead over its competitors. For driving and drilling power the DeWalt drills are the best available.
Something that Makita used to do is not have holes at the back of the drill where your hand will cover the cooling vents. With their newer drills the venting was changed and now it is very easy to cover the vents and cut the cooling of the motor by half. Something to take note of when using the drill with both hands. When I am making holes in stucco I find myself using both hands with one hand on the back of the drill to add pressure. The new Blue Boar TCT hole cutters for stucco and wood make short work of the stucco or brick but a bit of pressure is needed to cut through the plywood and a second hand helps.
BLUE BOAR 6-1/4" (159mm) Stucco-Brick & Wood Tungsten Carbide Tipped TCT Hole Saw with 4" shank (M16 Thread), 10mm carbide pilot bit, ejection spring
I expect that the drills will hold up well based on my experience with other Makita cordless tools but that experience may not be typical for the brand. I would not recommend the reconditioned kits from Makita unless you have time to deal with their customer support people to get missing items or replace defective ones.
Images Product
Buy Factory-Reconditioned Makita 18V Cordless LXT Lithium-Ion 1/2" Hammer Driver-Drill Kit BHP454 Now
0 comments:
Post a Comment